CSA B415.1:22

Preface

This is the fourth edition of CSA B415.1, Performance testing of solid-biofuel-burning heating appliances. It supersedes the previous editions, published in 2010 and 2000 under the title Performance testing of solid-fuel-burning heating appliances, and published in 1992 under the title Performance Testing of Solid-Fuel-Burning Stoves, Inserts, and Low-Burn-Rate Factory-Built Appliances.

This Standard can be used as a stand-alone document that can be referenced by the appropriate authority having jurisdiction (AHJ).

The major changes from the previous edition are as follows:

a) this Standard has been restructured to comply with current CSA Group requirements;

b) the general layout has been restructured to make this Standard easier to follow for each type of product covered;

c) the types of products covered by this Standard have been clarified and expanded;

d) site-built heating appliances and hybrid heaters have been added as new product types covered by this Standard;

e) definitions have been added for hybrid hydronic heaters and hybrid forced-air heaters;

f) certain definitions have been clarified and updated (e.g., factory-built fireplace, masonry heater, room heater);

g) reference publications have been updated to the latest editions;

h) informative Annex B, pertaining to the total combustible carbon method for determination of energy efficiency, has been deleted;

i) for many types of appliances, content has been replaced with a referenced standard (e.g., ASTM E2515, ASTM E3053), allowing for less text duplication, better harmonization with the United States Environmental Protection Agency (U.S. EPA), and improved alignment with other International or Regional Standards;

j) this Standard now includes references to and uses definitions from the CSA ISO 17225 series of Standards on graded solid biofuels;

k) emission requirements have been added for hybrid hydronic heaters and hybrid forced-air heaters;

l) emission limits for room heaters have been lowered and harmonized with the U.S. EPA;

m) emission limits for forced-air furnaces and hydronic heaters have been lowered and harmonized with the U.S. EPA, with compliance deadlines of January 1, 2025, and January 1, 2024, respectively;

n) an emission cap applicable to any single test run has been added for forced-air furnaces;

o) the test method for forced-air furnaces (i.e., duct velocity measurement) has been clarified and improved based on lab experience since this Standard was last published;

p) a test method has been developed using portable flue gas analyzers for measuring the gaseous emissions and thermal efficiency of site-built appliances;

q) test fuel characteristics for automatically fuelled appliances have been clarified and expanded;

r) CEN EN 303-5 has been recognized in this Standard for third-party certified automatically fed hydronic heaters with a nominal heat output between 50 and 500 kW;

s) an emission requirement (expressed in mg/Nm3) and a minimum delivered thermal efficiency requirement have been added for third-party certified automatically fed hydronic heaters tested to CEN EN 303-5; and

t) output and efficiency calculations have been modified to address appliances that generate electricity.

The CSA Technical Committee has endeavoured to make the test methodology of this Standard consistent with the U.S. EPA’s regulations, where possible. The interpretation of U.S. EPA regulations is periodically updated by the issuance of Applicability Determinations. Anyone using this Standard who also intends to seek U.S. EPA product approval should be fully conversant with all U.S. EPA requirements.

The Standards of Performance for New Residential Wood Heaters (Subpart AAA) and Method 1— Sample and Velocity Traverses for Stationary Sources were created by the U.S. Environmental Protection Agency (U.S. EPA). They are reproduced in Canada with permission from U.S. EPA.

Reprinted, with permission, from ASTM E2515-11 (2017): Standard Test Method For Determination Of Particulate Matter Emissions Collected By A Dilution Tunnel, ASTM E3053-18e1: Standard Test Method for Determining Particulate Matter Emissions from Wood Heaters Using Cordwood Test Fuel, and E2618-13 (2019): Standard Test Method for Measurement of Particulate Emissions and Heating Efficiency of Solid Fuel-Fired Hydronic Heating Appliances, copyright ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428. A copy of the complete standard may be obtained from ASTM International, www.astm.org.

CSA acknowledges that the development of this Standard was made possible, in part, by the financial support of the Hearth, Patio & Barbecue Association (HPBA).

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

Scope

1.1 Product range

This Standard specifies requirements for performance testing of solid-biofuel-burning heating appliances, including maximum emission rates.

1.2 Reporting metrics

This Standard specifies a method for determining

a) heat outputs;

b) appliance efficiencies;

c) emission levels and composition; and

d) electrical energy consumption and production.

1.3 Product types

This Standard applies to

a) Type 1: site-built heating appliances;

b) Type 2: room heaters;

c) Type 3: forced-air furnaces;

d) Type 4: hydronic heating appliances; and

e) Type 5: hybrid heating appliances.

Note: Typically, units tested under this Standard will have outputs less than 150 kW (500 000 BTU/h).

For the purposes of this Standard, solid-biofuel-burning appliances include manually and automatically fuelled systems (including add-ons and combinations).

1.4 Fuels

This Standard covers appliances that burn biomass fuels such as

a) cordwood;

b) wood chips;

c) wood pellets;

d) sawdust;

e) firelogs;

f) wood, paper, and other biomass pellets and briquettes; and

g) non-woody solid biofuels from agricultural, herbaceous, and fruit origins such as kernel corn, other grains, cherry pits, and pelletized or briquetted straw, hay, and corn stover.

1.5 Products not covered

This Standard does not apply to

a) factory-built fireplaces intended to be used primarily for aesthetic enjoyment and not as space heaters; and

b) solid fossil fuel appliances.

1.6 Emissions limits

Emission limits are expressed in both g/h and g/MJ (output) at the option of the manufacturer. Forced- air furnace and hydronic heater emission limits are expressed in g/MJ (output) only, with the addition that indoor automatically fed hydronic heater emissions are expressed in mg/Nm3 at a delivered minimum thermal efficiency when tested to CEN EN 303-5.

1.7 Units of measurement

The values given in SI units are the units of record for the purposes of this Standard. Where values are given in parentheses, they are for information and comparison only.

1.8 Terminology

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; and may is used to express an option or that which is permissible within the limits of the Standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.

An update to this product is available.

To receive notifications when an amendment, new edition or update is available to your standard no matter how you purchased it, please register on the Standards Update Service. After registering, enter the List ID for the relevant standard. The List ID can be found in the “CSA Standards Update” section within the first few pages of the standard you’ve purchased. Once notified, you can then update your standard accordingly.

PDF Format Purchased from the CSA Store

If you have purchased or subscribed to a standard from the CSA Store in PDF format, login to your CSA OnDemand^TM account to access the updated PDF.

Paper Format Purchased or Purchased from Reseller

If you have purchased a paper copy of the standard from the CSA Store or purchased a standard in paper or PDF format from one of our resellers, login to the Standards Update Service to download the updates in PDF format.