F280-12 (R2021)
Determining the required capacity of residential space heating and cooling appliances
détails du produit
Overview
It's imperative that residential space heating and cooling systems have the proper output capacity. Too little or too much capacity can create a dangerous and uncomfortable living environment. This revised standard provides guidelines for contractors and installers on calculating proper heating and cooling system energy capacity for appliances used in housing and small buildings of residential occupancy to which Part 9 of the National Building Code of Canada applies.
F280-12 Determining the Required Capacity of Residential Space Heating and Cooling Appliances also provides restrictions on selecting the output capacity of a specific space heating or cooling appliance or group of appliances.
F280-12
âą Provides a calculation method for determining the heat loss and heat gain of buildings for selecting the appropriate output capacity of a space heating appliance or group of appliances, and the output capacity of a cooling appliance or group of appliances.
âą Provides restrictions on selecting the output capacity of a specific space heating or cooling appliance or group of appliances.
âą Applies to space heating and cooling appliances used in residential occupancy, to which Part 9 of the National Building Code of Canada applies, where the appliances are permanently installed within the dwelling unit they serve.
âą Does not deal with detailed design and installation of space heating and cooling systems, but is based on distribution systems that comply with good engineering practices described in the applicable building codes and standards.
âą Works in conjunction with C22.2 NO. 280-13 Electric Vehicle Supply Equipment (Tri-national standard, with UL 2594 and NMX-J-677-ANCE-2013)
Preface
This is the third edition of CSA F280, Determining the required capacity of residential space heating and cooling appliances. It supersedes the previous edition published in 1990.
This Standard provides contractors, equipment manufacturers, building officials, and others involved in residential construction with updated calculation methods for determining the output capacity of all types of applicable residential space heating and cooling appliances to maintain specified indoor environmental conditions in Canadian homes. However, this Standard does not cover the detailed design and installation of residential space heating and cooling systems.
Microsoft ExcelÂź spreadsheets are linked to this Standard for calculating heat loss and heat gain associated with all types of common foundations. The spreadsheets can also be used to calculate some of the factors needed for determining air change, infiltration, and air leakage losses of the building. A description of the spreadsheets, along with instructions for accessing them, is provided in Annex F. Instructions for the use of the spreadsheets can also be found within the spreadsheets themselves.
Additional changes to this edition include calculations for determining heat loss due to continuous ventilation, air change heat loss for each room, heat gain through transparent and translucent building assemblies, and heat gain adjustments for shading.
Annex B provides a commentary on specific clauses in the Standard with additional information on the principles used for the modeling of foundations, air leakage, and windows. Annex B is also intended to outline, where they are not self-evident, the intent of and rationale behind the various requirements of this Standard in order to facilitate understanding and application of those requirements.
CSA acknowledges that the development of this Standard was made possible, in part, by the financial support of Natural Resources Canada (NRCan), the Ontario Ministry of Energy, BC Hydro, Manitoba Hydro, and Efficiency Nova Scotia.
CSA also wishes to acknowledge the efforts of the Housing, Buildings Communities and Simulation Group (HBCS) of CanmetENERGY Ottawa, a division of the Innovation and Energy Technology Sector (IETS) of Natural Resources Canada for their technical contribution towards the updating of the Standard; and Meteorological Service of Canada, a division of Environment Canada, for providing the weather data in the spreadsheet. The financial contributions from Enbridge Gas Distribution Inc. and Union Gas Limited for the development of the Microsoft ExcelÂź spreadsheets are also acknowledged. Finally, CSA acknowledges the work of Mindscape Innovations Group for finalizing the spreadsheets. Additionally, CSA wishes to acknowledge the financial contribution of Reliance Comfort Ltd. and the Heating, Refrigeration and Air Conditioning Institute of Canada (HRAI) for the preparation of amendments to this Standard.
CSA also acknowledges Brian Bradley of Natural Resources Canada, Sustainable Buildings and Communities Group, CanmetENERGY, for his valuable contribution to the development of this Standard and for his evaluation of the spreadsheets during the course of their development.
This Standard was prepared by the Technical Committee on Sizing of Residential Heating and Cooling Systems under the jurisdiction of the Strategic Steering Committee on Fuel-Burning Equipment and was formally approved by the Technical Committee.
Scope
1.1
This Standard provides a calculation method for determining the heat loss and heat gain of buildings (as described in Clause 1.3 below) for the purpose of selecting the appropriate output capacity of a space heating appliance or group of appliances and the output capacity of a cooling appliance or group of appliances.
1.2
This Standard also provides restrictions on selecting the output capacity of a specific space heating or cooling appliance or group of appliances.
1.3
This Standard applies to space heating and cooling appliances for use in housing and small buildings of residential occupancy to which Part 9 of the National Building Code of Canada applies, where the appliances are permanently installed within the dwelling unit they serve.
1.3A
This Standard also provides a method for verifying whether a software system produces heat loss and gain results that are representative of the results that would be obtained using a method that exactly follows the calculation method set out in this Standard.
1.3B
This Standard applies to software systems which are intended to be used to calculate heat loss and gain of homes according to this Standard.
1.4
This Standard does not deal with detailed design and installation of space heating and cooling systems, but is based on the assumption that the distribution system design complies with good engineering practice as described in the applicable building codes and standards.
1.5
The requirements of this Standard are expressed in SI (metric) units.
Note: The requirements in Clause 8 and Annexes G to K are expressed in Imperial and SI (metric) units.
1.6
In CSA Standards, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; may is used to express an option or that which is permissible within the limits of the standard; and can is used to express possibility or capability.
Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.
Notes to tables and figures are considered part of the table or figure and may be written as requirements.
Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
An update to this product is available.
To receive notifications when an amendment, new edition or update is available to your standard no matter how you purchased it, please register on the Standards Update Service. After registering, enter the List ID for the relevant standard. The List ID can be found in the âCSA Standards Updateâ section within the first few pages of the standard youâve purchased. Once notified, you can then update your standard accordingly.
PDF Format Purchased from the CSA Store
If you have purchased or subscribed to a standard from the CSA Store in PDF format, login to your CSA OnDemandTM account to access the updated PDF.
Paper Format Purchased or Purchased from Reseller
If you have purchased a paper copy of the standard from the CSA Store or purchased a standard in paper or PDF format from one of our resellers, login to the Standards Update Service to download the updates in PDF format.Â
Demander des autorisations de copyright
