B137 B PACKAGE-17

B137 B PACKAGE-17 Consists of:

B137.0-17 - Definitions, general requirements, and methods of testing for thermoplastic pressure piping

Preface

This is the tenth edition of CSA B137.0, Definitions, general requirements, and methods of testing for thermoplastic pressure piping. It supersedes the previous editions published in 2013, 2009, 2005, 2002, 1999, 1993, 1986, 1981, and 1973.

This Standard was initially published as part of CSA B137 Series-17, Thermoplastic pressure piping compendium. It was reissued as a stand-alone Standard in January 2019.

CSA B137.0 provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series. Wherever possible, individual Standards make reference to the relevant clauses in CSA B137.0.

Scope

1.1

This Standard specifies requirements for thermoplastic pressure piping. It includes reference publications, definitions, abbreviations, general requirements for materials, manufactured pipe and fittings, relevant test methods, and marking requirements.

Note: The terms pipe and piping, as well as tube and tubing, are used interchangeably in the CSA B137 Series.

1.2

This Standard is intended to be used in conjunction with one of the other Standards in the CSA B137 Series to form a complete Standard for a particular product.

1.3

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; and may is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

--------------------------------------------------------------------------------------------------------------------------------

B137.5-17 - Crosslinked polyethylene (PEX) tubing systems for pressure applications

Preface

This is the ninth edition of CSA B137.5, Crosslinked polyethylene (PEX) tubing systems for pressure applications, which supersedes the previous editions published in 2013, 2009, 2005, 2002, 1999, 1997, 1996, and 1989.

This Standard was initially published as part of CSA B137 Series-17, Thermoplastic pressure piping compendium. It was reissued as a stand-alone Standard in January 2019.

CSA B137.0 provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series. Wherever possible, individual Standards make reference to the relevant clauses in CSA B137.0.

Scope

1.1

This Standard specifies requirements for crosslinked polyethylene (PEX) tubing systems, comprised of tubing and fittings.

Tubing covered by this Standard is made in Standard Dimensional Ratio 9 (SDR 9).

Systems are pressure rated at three temperatures: 1105 kPa at 23 °C, 690 kPa at 82 °C, and 550 kPa at 93 °C, with a maximum working pressure of 690 kPa at 82 °C. Systems are intended for use in potable water distribution systems or other applications, including municipal water service lines, reclaimed water distribution, radiant panel heating and cooling systems, hydronic baseboard heating systems, snow and ice melting heating systems, building services piping, compressed air distribution, and ground source geothermal systems, provided that the PEX tubing systems covered herein comply with the applicable code requirements. Residential and commercial systems are included.

Note: The requirements and test methods specified in this Standard can involve hazardous materials, operations, and equipment. This Standard does not purport to address all of the safety problems associated with its use. Users of this Standard are responsible for establishing appropriate safety and health practices and determining the applicability of regulatory limitations before using this Standard.

1.2

This Standard specifies requirements for

a) materials;

b) quality of work;

c) tubing;

d) metal components of fittings;

e) fittings;

f) interior liners;

g) dimensions;

h) hydrostatic capability;

i) marking for tubing and fittings; and

j) marking for flexible pre-insulated tubing.

1.3

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; and may is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

--------------------------------------------------------------------------------------------------------------------------------

B137.6-17 - Chlorinated polyvinylchloride (CPVC) pipe, tubing, and fittings for hot-and cold-water distribution systems

Preface

This is the ninth edition of CSA B137.6, Chlorinated polyvinylchloride (CPVC) pipe, tubing, and fittings for hot- and cold-water distribution systems, which supersedes the previous editions published in 2013, 2009, 2005, 2002, 1999, 1996, 1983, and 1971.

This Standard was initially published as part of CSA B137 Series-17, Thermoplastic pressure piping compendium. It was reissued as a stand-alone Standard in January 2019.

CSA B137.0 provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series. Wherever possible, individual Standards make reference to the relevant clauses in CSA B137.0.

Scope

1.1

This Standard covers chlorinated polyvinylchloride (CPVC) pipe, tubing, and fittings having standard dimension ratio 11 (SDR 11), and Schedules 40 and 80 pipe in pipe sizes whose dimension ratio does not exceed 11, for use in hot- and cold-water distribution systems at a maximum working pressure of 690 kPa and a maximum working temperature of 82 °C.

1.2

This Standard specifies requirements for materials, quality of work, dimensions and tolerances, hydrostatic sustained pressure strength, thermocycling resistance, solvent cement, joint strength, and markings.

1.3

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; and may is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

--------------------------------------------------------------------------------------------------------------------------------

B137.10-17 - Crosslinked polyethylene/aluminum/crosslinked polyethylene (PEX-AL-PEX) composite pressure-pipe systems

Preface

This is the eighth edition of CSA B137.10, Crosslinked polyethylene/aluminum/crosslinked polyethylene (PEX-AL-PEX) composite pressure-pipe systems, which supersedes the previous editions published in 2013, 2009, 2005, 2002, 1999, 1998, and 1991.

This Standard was initially published as part of CSA B137 Series-17, Thermoplastic pressure piping compendium. It was reissued as a stand-alone Standard in January 2019.

CSA B137.0 provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series. Wherever possible, individual Standards make reference to the relevant clauses in CSA B137.0.

Scope

1.1

This Standard covers crosslinked polyethylene/aluminum/crosslinked polyethylene (PEX-AL-PEX) macrocomposite pipe consisting of a welded aluminum (AL) tube laminated by a melt adhesive to layers of crosslinked polyethylene (PEX) inside and outside the aluminum tube. This Standard also covers fittings (connectors) for use with PEX-AL-PEX pipe. The pipes covered in this Standard are pressure rated for 1380 kPa at 23 °C or 860 kPa at 82 °C, or both.

Systems are intended for use in potable water distribution systems or other applications, including municipal water service lines, reclaimed water distribution, radiant panel heating systems, hydronic baseboard heating systems, snow and ice melting systems, building services piping, compressed air distribution, ground source geothermal systems, underground irrigation, and compressed gas distribution (not including fuel gases), provided that the PEX-AL-PEX systems comply with the applicable code requirements. Residential and commercial systems are included.

Note: The complete structure, consisting of the aluminum, melt adhesive, and layers of crosslinked polyethylene intimately bonded together, is known as pipe. For the purposes of this Standard, the layer of welded aluminum, or the internal and external layer of crosslinked polyethylene, is known as a tube. Tubes, intimately bonded together by the melt adhesive, form a pipe.

1.2

This Standard specifies requirements for materials, quality of work, dimensions, thermocycling resistance, sustained pressure performance, delamination resistance, and marking.

Notes:

1) In developing the hydrostatic design basis for PEX-AL-PEX pipes, in accordance with CSA B137.0, pressure has been substituted for fibre stress.

2) The pressure rating of PEX-AL-PEX pipes is contingent on the thickness of the aluminum metal reinforcing layer. Pipes having the same dimension ratio but different metal reinforcing layer thicknesses will have different pressure ratings. The dimension ratio therefore cannot be used, as it is with homogeneous walled pipes, to assess changes in pressure rating with wall thickness variation.

1.3

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; and may is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

--------------------------------------------------------------------------------------------------------------------------------

B137.11-17 - Polypropylene (PP-R) pipe and fittings for pressure applications

Preface

This is the seventh edition of CSA B137.11, Polypropylene (PP-R) pipe and fittings for pressure applications, which supersedes the previous editions published in 2013, 2009, 2005, 2002, 1999, and 1993.

This Standard was initially published as part of CSA B137 Series-17, Thermoplastic pressure piping compendium. It was reissued as a stand-alone Standard in January 2019.

CSA B137.0 provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series. Wherever possible, individual Standards make reference to the relevant clauses in CSA B137.0.

Scope

1.1

This Standard covers pipe and fittings made of random copolymerized polypropylene (PP-R) intended for use in pressure applications such as hot and cold potable water distribution systems, process piping, reclaimed/recycled water systems, water service, and geothermal systems. Piping system components covered by this Standard are classified based on dimension ratio in sizes NPS-3/8 to NPS-28, and are joined using socket-type heat-fusion joints, saddle welding joints (fusion outlet), electrofusion joints, and butt welding.

Piping in SDR 11 and higher covered by this Standard is intended for use in cold water only systems or heating systems operating at 310 kPa or less.

1.2

This Standard specifies requirements for materials, dimensions, hydrostatic sustained pressure performance, heat reversion, apparent tensile strength, cold impact resistance, and marking.

1.3

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; and may is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

--------------------------------------------------------------------------------------------------------------------------------

B137.18-17 - Polyethylene of raised temperature resistance (PE-RT) tubing systems for pressure applications

Preface

This is the second edition of CSA B137.18, Polyethylene of raised temperature resistance (PE-RT) tubing systems for pressure applications, which supersedes the previous edition published in 2013.

This Standard was initially published as part of CSA B137 Series-17, Thermoplastic pressure piping compendium. It was reissued as a stand-alone Standard in January 2019.

CSA B137.0 provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series. Wherever possible, individual Standards make reference to the relevant clauses in CSA B137.0.

Scope

1.1

This Standard specifies requirements for polyethylene of raised temperature (PE-RT) tubing systems that are comprised of tubing and fittings.

Tubing covered by this Standard is made in Standard Dimensional Ratio 9 (SDR 9).

Systems are pressure rated at two temperatures: 1105 kPa at 23 °C and 690 kPa at 82 °C. Systems are intended for use in potable water distribution systems or other applications, including municipal water service lines, reclaimed water distribution, radiant panel heating and cooling systems, hydronic baseboard heating systems, snow and ice melting heating systems, building services piping, compressed air distribution, and ground source geothermal systems, provided that the PE-RT tubing systems covered in this Standard comply with the applicable code requirements. Residential and commercial systems are included.

Note: The requirements and test methods specified in this Standard can involve hazardous materials, operations, and equipment. This Standard does not purport to address all potential safety problems associated with its use. Before using this Standard, users are responsible for establishing appropriate health and safety practices and determining the applicability of any regulatory limitations.

1.2

This Standard specifies requirements for

a) materials;

b) quality of work;

c) tubing;

d) metal components of mechanical fittings;

e) fittings;

f) interior liners;

g) dimensions;

h) hydrostatic capability;

i) marking for tubing and fittings; and

j) marking for flexible pre-insulated tubing.

1.3

In this Standard, shall is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; should is used to express a recommendation or that which is advised but not required; and may is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.