Codes & Standards - Purchase
CAN/CSA-C22.2 NO. 60745-1-07 (R2022)
Hand-held motor-operated electric tools - Safety - Part 1: General requirements (Binational standard with UL 60745-1)
Product Details
Preface
This is the harmonized CSA Group and UL standard for Hand-Held Motor-Operated Electric Tools — Safety — Part 1: General Requirements. It is the third edition of CAN/CSA-C22.2 No. 60745-1, and the fourth edition of UL 60745-1. This harmonized standard has been jointly revised on June 10, 2022. For this purpose, CSA Group and UL are issuing revision pages dated June 10, 2022.
This harmonized standard is based on IEC Publication 60745-1: fourth edition Hand-Held Motor-Operated Electric Tools — Safety — Part 1: General Requirements, issued April 2006. IEC 60745-1 is copyrighted by the IEC.
This harmonized standard was prepared by CSA Group and Underwriters Laboratories Inc. (UL).
This standard is considered suitable for use for conformity assessment within the stated scope of the standard.
This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.
Scope
This part of IEC 60745 deals with the safety of hand-held motor-operated or magnetically driven electric tools, the rated voltage of the tools being not more than 250 V for single-phase a.c. or d.c. tools, and 440 V for three-phase a.c. tools.
So far as is practicable, this standard deals with the common hazards presented by hand-held tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools.
Tools with an electric heating element are within the scope of this standard. They should also comply with relevant parts of IEC 60335.
Requirements for motors not isolated from the supply, and having basic insulation not designed for the rated voltage of the tools, are given in Annex B. Requirements for rechargeable battery powered motor-operated or magnetically driven tools and the battery packs for such tools are given in Annex K. Those for such tools that are also operated and/or charged directly from the mains or a non-isolated source are given in Annex L.
Hand-held electric tools, hereinafter referred to as tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard.
Requirements for such supports or working stands are given in Annex M.
This standard does not apply to:
- hand-held tools intended to be used in the presence of explosive atmosphere (dust, vapour or gas);
- hand-held tools used for preparing and processing food;
- hand-held tools for medical purposes (IEC 60601);
- heating tools which are covered by IEC 60335-2-45.
For hand-held tools intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary.
For hand-held tools intended to be used in tropical countries, special requirements may be necessary.
NOTE Attention is drawn to the fact that in many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities, etc.
CAN/CSA-C22.2 NO. 60745-1-04
Hand-Held Motor-Operated Electric Tools - Safety - Part 1: General Requirements (Bi-National standard, with UL 60745-1)
CAN/CSA-C22.2 NO. 745-4-1-95 (R1999)
Sécurité des outils portatifs à batterie - Quatrième partie: Exigences particulières pour les perceuses (norme binationale avec UL 745-4-1)
CAN/CSA-C22.2 NO. 745-3-95 (R1999)
Safety of Portable Battery-Operated Tools - Part 3: General Requirements (Bi-National standard, with UL 745-3)
CAN/CSA-C22.2 NO. 745-1-95 (R1999)
Safety of Portable Electric Tools - Part 1: General Requirements (Bi-National standard, with UL 745-1)
An update to this product is available.
To receive notifications when an amendment, new edition or update is available to your standard no matter how you purchased it, please register on the Standards Update Service. After registering, enter the List ID for the relevant standard. The List ID can be found in the “CSA Standards Update” section within the first few pages of the standard you’ve purchased. Once notified, you can then update your standard accordingly.
PDF Format Purchased from the CSA Store
If you have purchased or subscribed to a standard from the CSA Store in PDF format, login to your CSA OnDemandTM account to access the updated PDF.
Paper Format Purchased or Purchased from Reseller
If you have purchased a paper copy of the standard from the CSA Store or purchased a standard in paper or PDF format from one of our resellers, login to the Standards Update Service to download the updates in PDF format.
eBook Format Purchased
If you have purchased a standard in eBook format, login to the CSA Reader App to download the updated version of the standard.
Request Copyright Permissions
- Free updates to the latest version
- Access historical versions
- Access all supported languages
GST REG No R119441681
QST REG No R1006017360
