Preface
This is the harmonized ANCE, CSA Group, and ULSE Standard for Plugs, Receptacles, and Cable Connectors of the Pin and Sleeve Type. It is the First edition of NMX-J-719-ANCE, the Fifth edition of CSA C22.2 No. 182.1, and the Fifth edition of UL 1682. This edition of CSA-C22.2 No. 182.1 supersedes the previous edition published in February 2014. This edition of UL 1682 supersedes the previous edition published on February 7, 2014. This harmonized standard has been jointly revised on March 28, 2024. For this purpose, CSA Group and ULSE are issuing revision pages dated March 28, 2024, and ANCE is issuing a new edition dated March 28, 2024.
This harmonized Standard was prepared by the Association of Standardization and Certification, (ANCE), CSA Group, and ULSE Inc. (ULSE).
The efforts and support of the Technical Harmonization Subcommittee, 23H, on the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA), are gratefully acknowledged.
This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.
The present Mexican standard was developed by the CT 23 – Accesorios eléctricos (Artefactos eléctricos) from the Comite de Normalizacion de la Asociacion de Normalizacion y Certificacion, A.C., CONANCE, with the collaboration of the plugs, receptacles and conductors manufacturers and users.
This Standard has been approved by the American National Standards Institute (ANSI) as an American National Standard.
This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.
Scope
1.1
This standard applies to pin and sleeve type plugs, receptacles, power inlets, and connectors, rated up to 800 amperes and up to 600 volts ac or dc, and which may include up to eight pilot contacts. These devices are intended to provide power from branch circuits, or are for direct connection to the branch circuit in accordance with the Canadian Electrical Code Part I, the National Electrical Code (NEC), ANSI/NFPA 70, and the Mexican Electrical Code, NOM 001 SEDE, using copper conductors, for use in either indoor or outdoor nonhazardous locations. In Canada, the terminals of a device intended to accommodate aluminum conductors also comply with CSA C22.2 No. 65.
1.2
This standard does not apply to single conductor pin and sleeve devices. Single pole locking-type separable connectors are covered by CSA C22.2 No. 1691/UL 1691.
1.3
This standard does not apply to:
a) Devices molded integrally with flexible cord or cable that are covered by UL 817, CSA C22.2 No. 21, and NMX-J-195-ANCE;
b) General and special use devices, such as attachment plugs, receptacles, cord connectors, inlets, current taps, flatiron and appliance plugs, that are covered by UL 498, CSA C22.2 No. 42, CSA C22.2 No. 57, CSA C22.2 No. 182.2, NMX-J-412-ANCE, NMX-J-412/2-1-ANCE, NMXJ-412/2-2-ANCE, NMX-J-412/2-3-ANCE, NMX-J-412/2-4-ANCE, NMX-J-412/2-5-ANCE, and NMX-J-412/2-6-ANCE;
c) Single and multi-pole connectors intended for connection to copper conductors, for use in data, signal, control and power applications within and between electrical equipment, where exposed, that are covered by UL 1977 and CSA C22.2 No. 182.3;
d) Devices intended for use in hazardous (Classified) locations that are covered by UL 1203 and CSA C22.2 No. 159; and
e) Products such as switched interlocks that are covered by UL 508 and CSA C22.2 No. 14.