Codes & Standards - Subscribe
ANSI Z21.8-1994 (R2017)
Installation of Domestic Gas Conversion Burners
SKU: 2701190
Published by CSA Group
Publication Year 1994
Reaffirmed in 2017
0 Edition
Product Details
Scope
1.1 Applicability
This Standard applies to the installation of a conversion burner with an input of 400,000 Btu per hour (117 228 W) or less and design certified as complying with the Standard for Domestic Gas Conversion Burners, ANSI Z21.17.
This Standard, in conjunction with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1, is applicable to situations where an appliance is to be converted to gas with a conversion burner, provided it can be demonstrated under Parts 2 and 3 that such a conversion can be made with safety, economy and in the best interest of the consumer.
All references to psi throughout this standard are to be considered gage pressure, unless otherwise specified.
Exhibit contains a list of standards specifically referenced in this standard, and sources from which these reference standards may be obtained.
1.2 Safe and Satisfactory Operation
Once the decision has been made to convert an appliance from another fuel to gas, safe and satisfactory operation will be dependent on a number of factors.
Among these are:
a) Proper analysis of the feasibility of conversion;
b) Proper selection of the burner to be used;
c) Proper selection of the draft hood or barometric draft regulator to be used;
d) Following the instructions contained in this standard; and
e) Following the installation instructions provided with the conversion burner.
For further information or assistance, the appliance manufacturer should be contacted. In no case should the appliance be modified beyond the recommendation of the appliance manufacturer. If the manufacturer cannot be contacted, the local gas supplier should be consulted.
1.3 Installation
The responsibility for a safe and satisfactory installation is shared by the agency determining the feasibility and selection of the burner, the installer, and the local authority having jurisdiction. In many areas a permit is required. Obtaining this permit is the responsibility of the installer. Maintenance and reporting of possible improper operation is the responsibility of the user. It is the responsibility of the installer to inform the user of the correct operation and maintenance.
1.1 Applicability
This Standard applies to the installation of a conversion burner with an input of 400,000 Btu per hour (117 228 W) or less and design certified as complying with the Standard for Domestic Gas Conversion Burners, ANSI Z21.17.
This Standard, in conjunction with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1, is applicable to situations where an appliance is to be converted to gas with a conversion burner, provided it can be demonstrated under Parts 2 and 3 that such a conversion can be made with safety, economy and in the best interest of the consumer.
All references to psi throughout this standard are to be considered gage pressure, unless otherwise specified.
Exhibit contains a list of standards specifically referenced in this standard, and sources from which these reference standards may be obtained.
1.2 Safe and Satisfactory Operation
Once the decision has been made to convert an appliance from another fuel to gas, safe and satisfactory operation will be dependent on a number of factors.
Among these are:
a) Proper analysis of the feasibility of conversion;
b) Proper selection of the burner to be used;
c) Proper selection of the draft hood or barometric draft regulator to be used;
d) Following the instructions contained in this standard; and
e) Following the installation instructions provided with the conversion burner.
For further information or assistance, the appliance manufacturer should be contacted. In no case should the appliance be modified beyond the recommendation of the appliance manufacturer. If the manufacturer cannot be contacted, the local gas supplier should be consulted.
1.3 Installation
The responsibility for a safe and satisfactory installation is shared by the agency determining the feasibility and selection of the burner, the installer, and the local authority having jurisdiction. In many areas a permit is required. Obtaining this permit is the responsibility of the installer. Maintenance and reporting of possible improper operation is the responsibility of the user. It is the responsibility of the installer to inform the user of the correct operation and maintenance.
items 1 - of 1 result(s)
View 20 | View 100
Request Copyright Permissions
